Basic Info.
Lifting Eye Type
Flat Eye
Color
White/Yellow/Red /OEM
Transport Package
Steel Drum or Woven Bag or as Required
Product Description
Product Specifications and Dimensions Vertical lifting spreader
Only applicable to the hoisting of the roll. There is no opening and closing mechanism, and only the round steel lifting lug and the rope ring without joint are needed to realize the whole lifting process.
Daily maintenance of vertical lifting plate spreader
1.During the use of the spreader, if the spinner rotation is not flexible or not in place, the adjustment nut should be checked, and then the following parts should be checked:
(1) Whether the tension spring of the pawl is damaged, if it is damaged, it should be replaced;
(2) Whether the transmission mechanism is stuck, such as stuck, is poor lubrication, it should be filled with lubricating oil (or grease) at the active connection of the transmission mechanism. If the guide pin is too tight, loosen the nut appropriately. If the connection is loose, the transmission pipe or other rod deformation, it should be corrected;
(3) Whether the stretch of the buffer spring is too small, if too small, it should shorten the length of the wire rope connected with the buffer spring.
2.The indicating marking paint on the spreader indicator board should be prevented from falling off during use. Once found, it is necessary to fill the paint of the original indicating mark in time.
3. For the wire rope on the spinner, it should be cleaned and coated with lubricating oil or grease in a timely manner, especially at the bend of the wire rope.
4. For the main stress components, suspension rings, twistlocks, ear plates and rigging shackles, under normal use conditions, they should be inspected at least once every 3 months, without cracks and serious deformation.
5. All oil cups, including the ratchet mechanism oil cup, the oil cup on the sliding bearing seat and the oil cup of the spinner lock box, the main active connection should be filled with oil according to the use of the situation.
6. Often check whether the rope card is loose, whether the buffer spring is over-stretched, and deal with the problem in time.
7. Each spreader shall not exceed the rated lifting weight, and the buffer spring shall not be overstretched.
8. The lifting process should be smoothly lifted to avoid deformation due to mutual impact between the lifting gear and the crane or other equipment.
Overview of billet lifting pliers and self-closing strip coil clamp
The clamp is mainly composed of seven parts: hanging beam, connecting rod, opening and closing mechanism, synchronizer, clamp arm, support plate and clamp teeth.
1. Hanging beam
The hanging beam is a part connected with the sky coupler, which has three kinds of structures: the hanging ring shackle connection, the sling sling connection and the lifting lug connection.
2. Connecting rod
The connecting rod is the connection between the hanging beam and the clamp arm.
3. Opening and closing mechanism
The opening and closing mechanism has the form of manual lifting rod type, (automatic) double hook type, (automatic) single hook type, (automatic) turnlock type and so on.
4. Synchronizer
Synchronizer is a device to ensure that each clamp arm moves synchronously.
5. Clamp arm
The clamp arm is the main forcing-strengthening component of the fixture, through which the billet is picked up.
6. Support plate
The support plate is the supporting part of the billet fixture. The support plate is supported on the upper surface of the billet to ensure the smooth operation of the opening and closing mechanism of the billet fixture.
7. Clamp teeth
The clamp teeth have the structure of pin shaft coupling, dovetail coupling and slot splicing. The clamp teeth are the main parts in direct contact with the billet, which determines the reliability of the billet clamping fixture.
The tongs are divided into horizontal steel tongs, vertical steel tongs, DHQL flat tongs,DSQA vertical tongs, vertical tongs,DSQK vertical tongs,DHQA flat tongs and other steel tongs according to the different methods of use. All kinds of tongs are made of high quality steel, safe and reliable, compact structure, light weight, etc. It is used with fixed hanging beam to adjust the width of the clamp rail quickly and easily. The application range is very wide, such as: shipyard, steel structure installation, steel market, machining, steel plate welding, steel plate cutting, steel plate horizontal handling, steel plate vertical moving and other workplaces need such products.
Overview of beam hanger and rail clamp:
Fixed on the beam, suspension block, electric hoist and sling.
The test load is 2 times the maximum working load and the breaking load is 4 times the maximum working load.
1. Hanger: in electroplating and related operations, used to suspend the workpiece and current to the workpiece frame.
There are many forms of hangers, there are general hangers that can apply several common parts, and there are special hangers for large quantities of parts. For geometrically complex plating parts, some should be equipped with auxiliary anode, auxiliary cathode or shielding plate.
The basic principles of the design of the hanger are: sufficient mechanical strength and good electrical conductivity, light weight, easy loading and unloading, and solid contact between the parts and the hanger.
The clamp is mainly composed of seven parts: hanging beam, connecting rod, opening and closing mechanism, synchronizer, clamp arm, support plate and clamp teeth.
2. Hang the beam
The hanging beam is a part connected with the sky coupler, which has three kinds of structures: the hanging ring shackle connection, the sling sling connection and the lifting lug connection.
3. Connecting rod
The connecting rod is the connection between the hanging beam and the clamp arm.
4. Opening and closing mechanism
The opening and closing mechanism has the form of manual lifting rod type, (automatic) double hook type, (automatic) single hook type, (automatic) turnlock type and so on.
5. Synchronizer
Synchronizer is a device to ensure that each clamp arm moves synchronously.
6. Pliers arm
The clamp arm is the main forcing-strengthening component of the fixture, through which the billet is picked up.
7. Support plate
The support plate is the supporting part of the billet fixture. The support plate is supported on the upper surface of the billet to ensure the smooth operation of the opening and closing mechanism of the billet fixture.
8. Clamp teeth
The clamp teeth have the structure of pin shaft coupling, dovetail coupling and slot splicing. The clamp teeth are the main parts in direct contact with the billet, which determines the reliability of the billet clamping fixture.
Ingot spreader:
The clamp adopts the working principle of automatic opening and closing, its structure is simple and reasonable, the action is flexible, and the lifting is safe and reliable. It does not need to provide any power source, rely on self-weight locking, opening and closing device positioning, automatically realize the opening and closing action of the jaws
Daily maintenance of steel fixture and ingot sling
1. During the use of the spreader, if the spinner rotation is not flexible or not in place, the adjustment nut should be checked, and then the following parts should be checked:
(1) Whether the tension spring of the pawl is damaged, if it is damaged, it should be replaced;
(2) Whether the transmission mechanism is stuck, such as stuck, is poor lubrication, it should be filled with lubricating oil (or grease) at the active connection of the transmission mechanism. If the guide pin is too tight, loosen the nut appropriately. If the connection is loose, the transmission pipe or other rod deformation, it should be corrected;
(3) Whether the stretch of the buffer spring is too small, if too small, it should shorten the length of the wire rope connected with the buffer spring.
2. The indicating marking paint on the spreader indicator board should be prevented from falling off during use. Once found, it is necessary to fill the paint of the original indicating mark in time.
3. For the wire rope on the spinner, it should be cleaned and coated with lubricating oil or grease in a timely manner, especially at the bend of the wire rope.
4. For the main stress components, suspension rings, twistlocks, ear plates and rigging shackles, under normal use conditions, they should be inspected at least once every 3 months, without cracks and serious deformation.
5. All oil cups, including the ratchet mechanism oil cup, the oil cup on the sliding bearing seat and the oil cup of the spinner lock box, the main active connection should be filled with oil according to the use of the situation.
6. Often check whether the rope card is loose, whether the buffer spring is over-stretched, and deal with the problem in time.
7. Each spreader shall not exceed the rated lifting weight, and the buffer spring shall not be overstretched.
8. The lifting process should be smoothly lifted to avoid deformation due to mutual impact between the lifting gear and the crane or other equipment.
Overview of beam hanger and rail clamp:
Suitable for lifting and handling of light and heavy rail.
Load 1 ton
The test load is 2 times the maximum working load and the breaking load is 4 times the maximum working load.
Two points are needed if the object is too long.
1. Hanger: in electroplating and related operations, used to suspend the workpiece and current to the workpiece frame.
There are many forms of hangers, there are general hangers that can apply several common parts, and there are special hangers for large quantities of parts. For geometrically complex plating parts, some should be equipped with auxiliary anode, auxiliary cathode or shielding plate.
The basic principles of the design of the hanger are: sufficient mechanical strength and good electrical conductivity, light weight, easy loading and unloading, and solid contact between the parts and the hanger.
The clamp is mainly composed of seven parts: hanging beam, connecting rod, opening and closing mechanism, synchronizer, clamp arm, support plate and clamp teeth.
2. Hang the beam
The hanging beam is a part connected with the sky coupler, which has three kinds of structures: the hanging ring shackle connection, the sling sling connection and the lifting lug connection.
3. Connecting rod
The connecting rod is the connection between the hanging beam and the clamp arm.
4. Opening and closing mechanism
The opening and closing mechanism has the form of manual lifting rod type, (automatic) double hook type, (automatic) single hook type, (automatic) turnlock type and so on.
5. Synchronizer
Synchronizer is a device to ensure that each clamp arm moves synchronously.
6. Pliers arm
The clamp arm is the main forcing-strengthening component of the fixture, through which the billet is picked up.
7. Support plate
The support plate is the supporting part of the billet fixture. The support plate is supported on the upper surface of the billet to ensure the smooth operation of the opening and closing mechanism of the billet fixture.
8. Clamp teeth
The clamp teeth have the structure of pin shaft coupling, dovetail coupling and slot splicing. The clamp teeth are the main parts in direct contact with the billet, which determines the reliability of the billet clamping fixture.
Steel plate clamp
The clamp adopts the working principle of manual opening and closing lever, which is simple and reasonable in structure, flexible in action and safe and reliable in lifting. Do not need to provide any power source, rely on self-weight locking, opening and closing device positioning, manual is the first clamping mouth opening and closing action.
Daily maintenance of steel fixture and ingot spreader
1. During the use of the spreader, if the spinner rotation is not flexible or not in place, the adjusting nut should be checked, and then the following parts should be checked:
(1) Whether the tension spring of the pawl is damaged, if it is damaged, it should be replaced;
(2) Whether the transmission mechanism is stuck, such as stuck, is poor lubrication, it should be filled with lubricating oil (or grease) at the active connection of the transmission mechanism. If the guide pin is too tight, loosen the nut appropriately. If the connection is loose, the transmission pipe or other rod deformation, it should be corrected;
(3) Whether the stretch of the buffer spring is too small, if too small, it should shorten the length of the wire rope connected with the buffer spring.
2. The indicating marking paint on the spreader indicator board should be prevented from falling off during use. Once found, it is necessary to fill the paint of the original indicating mark in time.
3. For the wire rope on the spinner, it should be cleaned and coated with lubricating oil or grease in a timely manner, especially at the bend of the wire rope.
4. For the main stress components, suspension rings, twistlocks, ear plates and rigging shackles, under normal use conditions, they should be inspected at least once every 3 months, without cracks and serious deformation.
5. All oil cups, including the ratchet mechanism oil cup, the oil cup on the sliding bearing seat and the oil cup of the spinner lock box, the main active connection should be filled with oil according to the use of the situation.
6. Often check whether the rope card is loose, whether the buffer spring is over-stretched, and deal with the problem in time.
7. Each spreader shall not exceed the rated lifting weight, and the buffer spring shall not be overstretched.
8. The lifting process should be smoothly lifted to avoid deformation due to mutual impact between the lifting gear and the crane or other equipment.
Ship the products:Company expansion activities display
){kind=link}